This is the FT232R and FT245R USB UART drivers. You do not normally need a UART driver for the devices as they are treated by the computer in the same way as the BM series devices. That noted that any driver which worked on the BM series devices will also now work with the R series devices. Note that there are some new functionalities which may now require the most recent drivers for the devices.
ft245r usb driver download
DOWNLOAD: https://byltly.com/2vHCpW
As of date any application which was coded for both the AM or BM series devices should still work with R series devices. There should be very few changes in this regard. You can also see some of the most common problems here. If the FT232R/FT245R asks for a new driver each time you connect to a device then you will note that Windows normally installs the drivers by serial number. Each time a new connection is made Windows will install the driver again for the new connected device.
This is normal as the R series device driver will need to be installed when it is connected to your system. FT and BM series components are not the same and not interchangeable. You will note that FT232R and FT245R are available in 28-pin SSOP and 32-pin QFN packages while the BM series devices were available in 32-pin LQFP and 32-pin QFN packages. You can also find the USB to UART driver on this website.
Right Click on the USB Serial Port and click on Update Driver Software which will then bring up another menu. Just like above you click Browse and then Browse to the location where you extracted the driver. Then click on Next as above. The port software will now install. If you are old enough to remember PcTel software modems when this UART software installs in the very same way. This is the FT232R and FT245R USB UART drivers.
If the driver listed is not the right version or operating system, search our driver archive for the correct version. Enter Future Tech FT245R into the search box above and then submit. In the results, choose the best match for your PC and operating system.
Once you have downloaded your new driver, you'll need to install it. In Windows, use a built-in utility called Device Manager, which allows you to see all of the devices recognized by your system, and the drivers associated with them.
Single chip USB to parallel FIFO bidirectional data transfer interface. Entire USB protocol handled on the chip - No USB-specific firmware programming required. Simple interface to MCU / PLD / FPGA logic with simple 4-wire handshake interface. Data transfer rate to 1 Megabyte / second - D2XX Direct Drivers. Data transfer rate to 300 kilobyte / second - VCP Drivers. FTDI's royalty-free VCP and D2XX drivers eliminate the requirement for USB driver development in most cases. New USB FTDIChip-IDTM feature. FIFO receive and transmit buffers for high data throughput. Adjustable receive buffer timeout. Synchronous and asynchronous bit bang mode interface options with RD# and WR# strobes allow the data bus to be used as a general purpose I/O port. Integrated 1024 Bit internal EEPROM for storing USB VID, PID, serial number and product description strings. Device supplied preprogrammed with unique USB serial number. Support for USB suspend / resume through PWREN# pin and Wake Up pin function.
The drivers listed above are all available to download for free from the FTDI website. Various 3rd Party Drivers are also available for various other operating systems - see the FTDI website for details.
M75177P : RS-485 Transiever. RS-485 TRANSCEIVER RS-485 TRANSCEIVER Each of the is a semiconductor IC with a built-in differential driver and a built-in differential receiver both of which meet the EIA standards RS-422A and RS-485. Common 5V single power supply With output control input (except M75179P) Driver 54 terminal resistor connectable between outputs. High output impedance.
MAX9325 : MAX9325 2:8 Differential Lvpecl/lvecl/hstl Clock And Data Driver. The MAX9325 low-skew, 2:8 differential driver extremely low output-to-output skew (50ps max) and part-to-part skew (225ps max). These make the device ideal for clock and data distribution across a backplane or board. The device selects one of the two differential HSTL or LVECL/LVPECL inputs and repeats them at eight differential outputs. Outputs are compatible.
SN65LVPE504 : Quad Channel (Half X4 Lane) PCI Express Gen II Redriver/Equalizer The SN65LVPE504 is designed to minimize the signal degradation effects such as crosstalk and inter-symbol interference (ISI) that limits interconnect distance between two devices. The input stage of each channel offers selectable equalization settings that can be programmed to match loss.
SN65LVCP114 : 14.2Gbps Quad Mux, Linear-Redriver With Signal Conditioning The SN65LVCP114 is an asynchronous, protocol-agnostic, low-latency QUAD mux, linear-redriver optimized for use in systems operating at up to 14.2 Gbps. The device linearly compensates for channel loss in backplane and active-cable applications. The architecture of SN65LVCP114 linear-redriver.
libFTDI is an open source library to talk to FTDI chips:FT230X
FT4232H / FT2232H
FT232R / FT245R
FT2232L / FT2232D / FT2232C
FT232BM / FT245BM (and the BL/BQ variants)
FT8U232AM / FT8U245AM
The library is linked with your program in userspace, no kernel driver required.libFTDI works perfectly with Linux, Windows, MacOS X and BSD variants thanks to libusb.
The MESA 7I43 is a low cost, general purpose programmable I/O card that connects to the host computer via USB or PC parallel port. The 7I43 uses a 200K or 400K gate Xilinx FPGA for all logic, so it is truly an Anything I/O card. The FPGA is downloadable from the USB or Parallel port bus side, and also has the capability of local configuration storage in an on card EEPROM. Efficient switching regulators are used for FPGA core and 3.3V power, allowing the 7I43 to be USB bus powered. The 7I43 can also be powered by an external 5V source. A FTDI FT245R USB interface chip is used for the USB interface. Drivers are available for Windows and Linux. The drivers avaliable for the FT245R make the software interface a simple buffered byte stream. Parallel port bus interface uses EPP mode. A 50 MHz oscillator provides the FPGA clock. This clock can be multiplied or divided in the FPGA for other clock rates. The 7I43 has 48 I/O bits available on two 50 pin connectors. Both connectors use I/O module rack compatible pinouts. All I/O bits are 5V tolerant, and have series and parallel termination options (DCI). The I/O connectors are compatible with our 7 series daughter cards for isolated I/O, motion control and other applications. Configurations are provided for simple GPIO, Smart Motion control (SoftDMC), host based motion control (HostMot2), and a waveform generator.
The USB2-F-7001 is a USB to CANbus adapter which incorporates the FTDI FT245R USB to FIFO interface IC device. The adapter provides a fast, simple way to connect CANbus devices to a host PC with a USB port.Each USB2-F-7001 contains a small internal electronic circuit board mounted inside of a plastic case capable of withstanding industrial temperature ranges. The FT245R datasheet, DS_FT245R, is available at The integrated electronics include a Microchip PIC with the ECAN controller. LEDs give a visual indication of the CANbus status.The USB2-F-7001 does not require a power supply. It is powered from the USB connection. The USB2-F-7001 requires 150mA and must be connected directly to a USB Host port, or a self-powered USB hub (i.e. with an external power supply). Bus-powered USB hubs are not supported since they cannot provide the required current.Flexible mounting allows the USB2-F-7001 to be used in a variety of applications, from a portable adapter to accompany a laptop to permanent installations in industrial and commercial locations.The enclosure incorporates a standard USB-B device connector for connection to an upstream host or hub port. CANbus signals are available on an industry-standard DE-9P connector conforming to the CAN-in-Automation (CiA) DS102-2 pin-out. The maximum CANbus data rate is 1Mbps. The USB2-F-7001 adapter requires USB device drivers, available free from www.easysync-ltd.com, which are used to make the USB2-F-7001 appear as a Virtual COM port (VCP). Communications in VCP mode are accomplished with ASCII commands to the CAN controller. Another USB device driver included with the download, the D2XX driver, can also be used with application software to directly access the FT245R, and used in conjunction with a CAN command Application Programming Interface (API) through the use of DLLs. The high-level API is listed in the documents section: USB2-F-7001 API Guide.Features: 2ff7e9595c
Comments